Theory and practice, equipment

hi friends how you can prevent automatic switch off during programing ? doc say "switch LOW BEAM ligth " what mean it ? thank you ;)

Hello, I would like to ask about MDFLASHER License 66 compatibility. I have a Fiat Tipo ABS unit with the following specifications: * Bosch ESP 9.0 * Bosch Part Number: 0265293961 * MCU: TMS570LS * EEPROM: 95640 According to the License 66 description, it supports Bosch ABS/ESP 9.0–9.1 units with TMS570 and EEPROM 95640, but the supported vehicle list only mentions Renault, Dacia, Nissan, and VAZ. Can you please confirm if License 66 supports reading and writing this Fiat Tipo ABS unit via OBD? I have attached photos of the ABS unit for reference. Thank you.

hi everyone iam trying to read\write dq381 new model (red rubber whree the sensor in the back) but i get error massage on 10:00:29 Unsupported TPROT version does anyone knows how to overcome this problem?

Pcm writes Toyota data, and writes to death leads to non-communication. How to connect or how to write now?

Hello, I need to read this ECM but I don't know which module to buy for the PCM Flash and if it does or which of your tools you recommend for these ECUs Thank you Eddy

Hello everyone. I would like to read/write Mazda skyactiv TCM with PCMFlash Module 80 via Openport 2.0 , Anyone have experience ? 1. If I connect power( PIN A+ C+ B-) and HS CAN (PIN E , F) to TCM Module connector directly , Can it be read/write via CAN port ? 2. Need to get PowerBox for PCMFlash , connect power( PIN A+ C+ B-) and HS CAN (PIN E , F) to TCM Module connector directly , Can it be read/write via CAN port ? 3. Need to get PowerBox for PCMFlash with BDM Mode(connect to chip) ? 4. Other better/easier way ? Thanks for your reply .

salut les amis tuner hp n'identifie pas ce système d'exploitation ecm 04896402AP sur ECM est écrit 1A3MI6PC de quel ECM s'agit-il ? merci les amis

Hello, What tool can read /write Lexus/Toyota 8966-78240 Denso ECU 275600-1481? Thanks!

Hello i have Toyota Prado 2.8L 1GDFTV. manufacture year 2017. Firmware ID 89663-60X56 Does anybody have solution for this firmware Adblue remove ?

Hello Need corect pinout for bench read . This is my firs edc17cp55 and have pcm flash modul 71 active and skanmatic pro interface. ecu is 0281032668 land rover dyscovery 3.0d from 2016 What is the step for this ecu. first need to read password and the read flash? can somone explain pleease procedure for this ecu type. THANK YOU

ECUTools is a team of highly qualified specialists who have all the necessary knowledge to help you in choosing and purchasing equipment. We are dynamically developing our business, constantly expanding the list of our partners, offering you all new products. We are looking forward to tomorrow with confidence and would like to share our confidence with you!

Guardant drivers installed. The program cannot be executed. Ask for help. My pc. windos 10 64bit

Hello ... anyone here speak english ?? i want informations about CombiLoader and mdflasher !!! i work in Opel and Chevrolet in Egypt i already pay CombiLoader and mdflasher want know more about it and make new friends from here

I am looking to edit DCM6.2 VIN mileage - any solution..? Thanks

Hello, I'm looking for some help or advice in reducing the throttle lag for the electronic throttle plate (drive by wire) for a toyota 2.5l 2arfe engine. I'm using BitEdit for tuning and I've made a few changes to a few throttle related maps and the sensor input without any success. Any help is much appreciated, Thanks, Shaun

Hello frind There is no one for me for edit file for toyota lexus & hyundai kia? And what is the best tools to read and write ? I use bitedit and bit box for toyota & lexus but I want to learn more. Thanks.

I need to read a Valeo V46.21 ECU using Combiloader, so I bought the Valeo V46 module but when tried to read the ECU, a message of "NO ECU answer" is displayed. Also same message is displayed when tried to do the ECU identification. I´m using CarDaq Plus as interfase. If I use the Drewtech tool (with CarDaq connected) I can scan the ECU, so I think the problem is not the interfase. Does anyone know how to solve this problem?

Hello members: I have a Hyundai Accent 2009 1.6L A/T with ECU Bosch MG 7.9.8, car does not start error code is P0605 (internal control module ROM error). Can someone of you check in the checksum is correct and fix it ? Thanks very much #34117 Accent 2009 USA 1.6L AT 39131-26BE6 MG798 GMC-9N6CPS4-A000 9003050099KH.rar

Hello members: I am looking for pinout connection for Suzuki Grand Vitara 1.6L M16A ME17.9.61 TC1724. Picture is here: https://www.google.com/search?q=bosch+me17.9.61&rlz=1C1TSNG_enCR455CR455&source=lnms&tbm=isch&sa=X&ved=0ahUKEwizxMbnh-3dAhVDp1kKHU_1COAQ_AUICigB&biw=1366&bih=608#imgrc=-tH_A_EvSZe8aM: Thanks very much for your help

Hello What better tools using to tune Hyundai petrol? Edit file...? Read and write ? Checksum?

Can you guys let me know which tool/software could read/write this ecu either by OBD or BSL mode.

someone can explain how to read sid307 just obd port? Can you read at the table? pinout and boot please Thank you

looking for stock file 89663-60B90 i need original file

im looking for a datalogger to use with tactrix bit edit for 05-08 honda legend. it has 2 oem wideband sensors

Hello everyone , please let me know if you have the Dump file for the Nissan Patrol 2010 / V8 23710-1LV0C thank you in advanced Best Regards Yousef